Home      News       Endress+Hauser Turbidity sensor CUE21-A1…

News

Endress+Hauser Turbidity sensor CUE21-A1A

无标题文档
Turbimax CUE21 / CUE22  

Application

On-line continuous monitoring of clean water: • Drinking water • Treated process water

Your benefits

• Versions with white light source and infrared light source available

• Fast and easy calibration – Complete primary calibration in less than 5 minutes – Verification in seconds

• Reduced calibration costs and quick response times thanks to low volume sample chamber

• Automatic continuous ultrasonic cleaning (Autoclean) increases cleaning intervals dramatically • Simple modular design • Easy to use and service

• Affordable thanks to modular microprocessor based technology

• Digital high-speed connections through RS-485 with Modbus Optional Features:

• Flow chamber for bubble suppression

• Reusable calibration ki

  Function and system design
Measuring principle


Turbidity measurement For turbidity measurement a light beam is sent through the medium and is diverted from its original direction by optically denser particels, e.g. solid matter particles.

Measuring methods


90° WL scattered light method The measurement uses the standardised 90° scattered light method acc. to U.S. EPA 180.1. The turbidity of the medium is determined by the amount of scattered light. The transmitted white light beam is scattered by the solid matter particles in the medium. The scattered beams are detected by scattered light receivers which are arranged at an angle of 90° to the white light source. 90° NIR scattered light method The measurement uses the standardized 90° scattered light method acc. to ISO 7027 / EN 27027. The turbidity of the medium is determined by the amount of scattered light. The transmitted light beam with a wavelength in the near-infrared range is scattered by the solid matter particles in the medium. The scattered beams are detected by scattered light receivers which are arranged at an angle of 90° to the infrared light source


 
Measuring system


The Turbimax CUE21 / CUE22 measuring system comprises:

• Turbimax turbidimeter with installed cuvette and desiccant pouch
• Connecting tubing with
– fittings for flow through assembly
– shutoff clamp
– backpressure valve
– drain vent screw (in pressurized systems)

• Sensor interconnect cable


 
 


Input

Measured variables
Turbidity
Measuring range
CUE21: 0 to 1000 NTU /FNU
CUE22: 0 to 100 NTU /FNU

 


Output

Output signal
4 to 20 mA, galvanically isolated
Signal on alarm
2 mA in case of an error
Load
max. 600 Ω
Communications port
Bi-directional RS-485, Modbus optional
Relays
Switching voltage: max. 240 VAC
Switching current: max. 2 A
Limit value and alarm
functions
Setpoint adjustment:
CUE21:
CUE22:
0 to 1000 NTU
0 to 100 NTU
Alarm delay: 0 to 30 s


Turbimax CUE21-A1A, compact infrared

Basic model
Turbimax  CUE21, compact infrared 
Power Supply:
A 100-240 VAC 
Output:
1 4-20 mA oder RS-485 
Version:
A Standard 

 
Power supply
Electrical connection
Power supply
100 to 240 VAC, 47 to 63 Hz, 80 VA switching power supply
 
Installation
Wall mounting
Turbimax CUE21 / CUE22 is recommended for indoor use.
When mounting the instrument note the following:
• Check that the temperature does not exceed the maximum permitted operating temperature range
(0 to 50 °C (32 to 122 °F)).
• Leave a free area of approx. 0.20 m (8.00") above the instrument. This will ensure enough room for
calibration and cuvette maintenance.
• Mount the instrument as close as possible to the sampling point to ensure a quick response time

(within 2 to 3 m (6 to 10 ft)).

 
Ordering information
Turbimax CUE21
compact device, infrared
Turbimax CUE22
compact device, white light